General Rinses 冲洗概述
Rinsing performed after electrocoating removes the thin layer of paint (the cream coat) which adheres to the deposited electrocoat film. Minor amounts of paint left on the deposited surface will cause defects. Bodies should be rinsed as soon as possible after they emerge from the paint tank and never later than one minute after that point.
电泳后冲洗可除去电泳漆膜表面附着的一薄层浮漆。电泳表面带有少量浮漆会引起漆膜缺陷，在车身露出电泳槽后要尽快冲洗，不能长于1分钟。
Highly efficient closed loop and gravity return rinse systems are necessary (see Figure 13). These systems use ultrafiltrate in the final stage and overflow each stage back to the paint tank where paint solids are recovered. Five stages of ultrafiltrate rinsing and two stages of DI water rinsing work well, configured as follows:
高效率的“闭路”，“重力回流”冲洗系统是必要的（见图16），这些系统是在最后一道工序用新鲜超滤液，随工序向前溢流返回电泳槽，以回收漆液固体份，此系统以五道超滤液冲洗加二道去离子水冲洗较好，编排如下：
Over Tank Rinse: Single or Double Header
槽上冲洗 单排或双排喷管
Recirculated Rinse 1: 30-45 Seconds
第一道循环超滤液冲洗： 30-45 秒
Dip Rinse: Complete Immersion
超滤液浸洗： 全浸没
Recirculated Rinse 2: 30-45 Seconds
第二道循环超滤液冲洗 30-45秒
Fresh Ultrafiltrate: Single or Double Header
新鲜超滤液冲洗 单排或双排喷管
Drain Area: Minimum of 60 Seconds
沥液区 最少60秒
Recirculated DI Rinse: 30-45 Seconds Fresh
循环去离子说： 30-45秒
Virgin DI Rinse: Single or Double Header
新鲜去离子水 单排或双排去离子水
Drain Time Between Rinses: 1 Minute
两道去离子水冲洗沥液时间：1分钟
All rinse tanks should be provided with good drainage so that cleaning will be effective. Acceptable materials of construction include coated steel tanks and stainless steel piping for rinses. Rinse walls, ceilings, and sanitary shields should be made of stainless or aluminized steel.
![]()
spraying.
所有的冲洗及泵池都要有良好的排液及搅拌装置，以保证清洗有效及迅速。超滤液冲洗方面可选用的结构材料包括涂有涂层的钢管及无镀层管。冲洗壁板，顶板及清洁屏蔽用不锈钢或涂有涂层的钢管及无镀层管。如使用无铅电泳漆，则只可用不锈钢PVC制造。
本文链接：http://phb.hhpj.net/post-318.html
电泳生产线冲洗
spraying.
所有的冲洗及泵池都要有良好的排液及搅拌装置，以保证清洗有效及迅速。超滤液冲洗方面可选用的结构材料包括涂有涂层的钢管及无镀层管。冲洗壁板，顶板及清洁屏蔽用不锈钢或涂有涂层的钢管及无镀层管。如使用无铅电泳漆，则只可用不锈钢PVC制造。